跳至主要内容

IPX5 and IPX6 Jet Hose Nozzles Water Ingress Protection Testing Equipment

https://www.pegotester.com/IPX5_IPX6_automatic_water_jet_nozzles_test_chamber.html#_jcp=3_18

1. Introduction

The IPX5 and IPX6 tests are made by spraying the enclosure from all practicable directions with a stream of water from standard test nozzles, the test nozzles (hose nozzles) with Φ6.3mm and Φ12.5mm diameter are strictly designed according to IEC60529 figure 6, and the test chamber can completely meet the test requirement of  IEC60529:1989 +A1:1999 +A2：2013 clauses 14.2.5 and 14.2.6.


IPX5 and IPX6 water ingress protection testing equipment is consisted by test tunnel and test chamber. Test nozzles are placed at the test tunnel with a distance of 2.8m from the center of the turntable, the turntable is inside the test chamber, the test nozzles can swing up and down automatically to spray the enclosure from all practicable directions. Built-in water tank and the water can be recycled, the test is controlled by PLC and touch screen, the delivery rate is 12.5L/min±5% for IPX3 test and 100L/min±5% for IPX4 test, the water pressure should be adjusted to achieve the specified delivery rates, test duration per square meter of enclosure surface area likely to be sprayed for 1 min, minimum test duration is 3min.


2. Features:

● For IPX5 and IPX6 waterproof testing.

● Integral structure, the nozzles are fixed on test tunnel, and can automatically swing up and down,operator just to fix the sample and start the test.

● Mainframe and turntable are made by SUS304# stainless steel to ensure rustless for long time.

● Built-in water tank, auto to control the water level with the help of water floating ball valve, and alarm at high or low level to protect from the damage caused by low water level.

● The water can be recycled.

● The delivery rate is manually controlled by rotameter.

● Adopts speed motor, the speed in the standard range, and can control the positive and negative direction automatically to prevent winding during live test.

● Jet nozzles: strictly designed according to IEC60529.

● Built-in outlet in the chamber (AC220V, 10A) for live test. The power on and power off time can be controlled: off (0~999min)-on (0~999min)-off (o-999min), fit for power on and off test.

● Test time can be set at the touch screen. Time setting range: 0~999min (adjustable), auto shut down when finish the test.

● Adopts 7 inch touch screen and Panasonic PLC. The electrical components adopt famous brands such as LS and Omron. The wiring technology meets the requirements of national standards. The electrical board layout is reasonable, the wiring is firm, and the marking is clear.

● Easy to operation, IPX5 and IPX6 testing can easy conversion.

● A LED lamp is installed in the test chamber to facilitate observation of the samples during the test.

● The jet nozzles can be automatically swing up and down, and the turntable can be rotated. It can basically realize all practicable directions spray on the sample surface. 



标签：

评论

发表评论

此博客中的热门博文

The material of standardized cookware in EN60350-2 version 2018 and version 2013

The standardized cookwares referred in this article are designed according to EN(IEC)60350-2 table (Z)3. The diameter of the cookware bottom (outside), diameter of the lid, lid hole circle diameter, number of holes on the circle, total cookware height (outside) and flatness of cookware bottom are specified in table (Z)3. The materials of side wall, cookware bottom and lid are different. In version 2018, the side wall of cookware is made of stainless steel AISI type 304, the cookware bottom is made of stainless steel AISI type 430, and and the lid is made of aluminium. In version 2013, the side wall of cookware is made of 1.4301 stainless steel, the cookware bottom is made of stainless steel 1.4016, and the lid is made of aluminium. Items Version 2018 Version 2013 Remark material thickness material thickness Side wall   stainless steel AISI  304 1mm±0.05mm 1.4301 stainless steel 1mm±0.05mm C ylindrical without handles or protrusions. Cookware bottom stainless steel AISI  ...
发表评论
阅读全文

vertical impact hammers

The vertical impact hammer is designed according to IEC60068-2-75 test Ehc, the hammer consists by a striking element which falls freely from rest through a vertical height on to the specimen surface held in a horizontal plane, and the fall of the striking element shall be along a guideway, the guideway shall not rest on the specimen and the striking element shall be free of the guideway on the striking the specimen , the mass of striking element is equal to equivalent mass . 2J striking element equip with Φ 40 mm*4 71 mm guideway, 5J striking element equip with Φ6 8 mm*3 85 mm guideway, 10J striking element equip with Φ8 9 mm* 337 mm guideway, 20J striking element equip with Φ10 8 mm* 520 mm guideway, 50J striking element equip with  Φ12 9 mm* 650 mm guideway. 
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文