跳至主要内容

Open-Type IPX5 and IPX6 Jet Nozzles Testing Equipment

 1. Introduction

IPX5 and IPX6 Jet Nozzles Water Jetproof Testing Equipment designed according to IEC60529 clause 14.2.5 and 14.2.6. The jet nozzles also be called as hose nozzles. Waterproof test simulates the condition of water jets and powerful water jets, which is mainly applied to electronic products, luminaire, electric components, motor and house-holding appliance. The waterproof test can help to judge the products’ performance, and provide the basis for design, improve and inspect.

This is a open-type equipment, which has no size and weight limit to the device under test. The equipment is consisted by control box, turntable, jet nozzles (diameter 6.3mm and 12.5mm) and nozzle holder. A 550L water tank is built in control box. The test distance is controlled by manual.

Jet hose nozzle with internal diameter of 6.3mm is for IPX5 jet-proof testing, the water flow rate is 12.5L/min, and test time is 1min/m2  and at lest 3 min. The test distance is 2.5m to 3m .

Jet hose nozzle with internal diameter of 12.5mm is for IPX6 strong jet-proof testing, the water flow rate is 100L/min, and test time is 1min/m2  and at lest 3 min. The test distance is 2.5m to 3m .

 

2. Features:

● For IPX5 and IPX6 waterproof testing.

● Mainframe and turntable are made by SUS304# stainless steel to ensure rustless for long time.

● Built-in water tank, auto to control the water level with the help of Water floating ball valve , and alarm at high or low level to protect from the damage caused by low water level.

● Adopts speed motor, the speed in the standard range, and can control the positive and negative direction (for live test, to prevent wire wrapping).

● Jet nozzles: strictly designed according to IEC60529.

● Built-in outlet in the turntable (AC220V, 10A) for live test. The power on and power off time can be controlled: off (0~999min)-on (0~999min)-off (o-999min).

● Test time can be set at the touch screen. Time setting range: 0~999min (adjustable), auto shut down when finish the test.

● Adopts 7 inch touch screen and Panasonic PLC.

● Easy to operation, IPX5 and IPX6 testing can easy conversion.

● Preset IPX5 and IPX6 test procedures, users only need to select the waterproof level, and the equipment will perform the test in accordance with the standard requirements.

 

3. Specification:

Control system

7 inch touch screen+Panasonic PLC

Outer size

1100mm*900mm*1300mm (L*W*H, control box)

600mm*600mm*800mm (L*W*H, turntable)

Water tank

550L, 800*600*1145 (mm), made by SUS304 stainless steel

Aperture diameter of IPX5 nozzle

6.3mm

Aperture diameter of IPX6 nozzle

12.5mm

Delivery rate for IPX5 (L/min)

12.5±0.625

Delivery rate for IPX6 (L/min)

100±5

Water pressure (Mpa)

As per the standard requirement

Flowmeter control

Manual control

Distance from specimen

2.5~3m (manual control)

Nozzle fixed way

Hand-held

Diameter of turntable

Φ600mm

Power of turntable

AC220V

Material

SUS304 stainless steel

Protection

Electric leakage, hydropenia, short circuit

Working power

AC 380V/ 50Hz, 3KW (3 phase 4 wire + protective ground wire)

Working conditions

5℃~35℃ (temperature), ≤85% (R.H.), 86kPa~106kPa (pressure)




标签：

评论

发表评论

此博客中的热门博文

The material of standardized cookware in EN60350-2 version 2018 and version 2013

The standardized cookwares referred in this article are designed according to EN(IEC)60350-2 table (Z)3. The diameter of the cookware bottom (outside), diameter of the lid, lid hole circle diameter, number of holes on the circle, total cookware height (outside) and flatness of cookware bottom are specified in table (Z)3. The materials of side wall, cookware bottom and lid are different. In version 2018, the side wall of cookware is made of stainless steel AISI type 304, the cookware bottom is made of stainless steel AISI type 430, and and the lid is made of aluminium. In version 2013, the side wall of cookware is made of 1.4301 stainless steel, the cookware bottom is made of stainless steel 1.4016, and the lid is made of aluminium. Items Version 2018 Version 2013 Remark material thickness material thickness Side wall   stainless steel AISI  304 1mm±0.05mm 1.4301 stainless steel 1mm±0.05mm C ylindrical without handles or protrusions. Cookware bottom stainless steel AISI  ...
发表评论
阅读全文

vertical impact hammers

The vertical impact hammer is designed according to IEC60068-2-75 test Ehc, the hammer consists by a striking element which falls freely from rest through a vertical height on to the specimen surface held in a horizontal plane, and the fall of the striking element shall be along a guideway, the guideway shall not rest on the specimen and the striking element shall be free of the guideway on the striking the specimen , the mass of striking element is equal to equivalent mass . 2J striking element equip with Φ 40 mm*4 71 mm guideway, 5J striking element equip with Φ6 8 mm*3 85 mm guideway, 10J striking element equip with Φ8 9 mm* 337 mm guideway, 20J striking element equip with Φ10 8 mm* 520 mm guideway, 50J striking element equip with  Φ12 9 mm* 650 mm guideway. 
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文