跳至主要内容

What is draught-proof enclosure?

The draught-proof enclosure is rectangular, with a double skin on top and on at leat three sides and with a solid base, the double skins are of perforated metal, space approximately 150mm apart, with regular perforations of 1mm to 2mm diameter, occupying about 40% of whole area of each skin. It is applied to thermal test of luminaire under the conditions of normal operation and abnormal operation. 

The inernal surface are painted with a matt paint. The three principal internal dimensions are each at least 900mm. There shall be a clearance of at least 200mm between the internal surfaces and any part of the largest luminaire for which the enclosure is designed (If it is required to test two or more luminaires in a large enclosure, be attention to take that radiation from one luminaie can not affect any other).

There is a clearance of at least 300mm above the top of the enclosure and around the perforated sides. The enclosure is at a location protected as far as possible from draughts and sudden changes in air temperature; it is also protected from sources of radiant heat.

A luminaire for direct fixing to a ceiling or wall shoulb be fixed to a mounting surface comprising a wood or wood-fiber board. A non-combustible insulating material is used if the luminaire not suitable for mounting on a combustible surface. The board is 15mm to 20mm thick, and extends no less than 100mm (but preferably not more than 200mm) beyond the normal projection of the smoothed outline of the luminaire. There is a clearance of at least 100mm between the board and the internal surfaces of the enclosure. The board is painted black with a matt non-metalic paint.

A lumianire for coner-fixing is fixed in a corner comprising two boards, each complying with the preceding requirements.

A third-board is required if the luminaire is to be fixed in a vertical corner immediately below a simulated ceiling.

Pego designed the draught-proof enclosure according to IEC60598-1 annex D, the size can be customized according to the customers requirement, for more details, please check the specification at.

Draught-proof enclosure: 
http://www.pegotester.com/draught_proof_enclosure.html#nSL=%5B5%2C6%2C7%2C8%5D&skeyword=draught&_pp=0_35


标签：

评论

发表评论

此博客中的热门博文

The material of standardized cookware in EN60350-2 version 2018 and version 2013

The standardized cookwares referred in this article are designed according to EN(IEC)60350-2 table (Z)3. The diameter of the cookware bottom (outside), diameter of the lid, lid hole circle diameter, number of holes on the circle, total cookware height (outside) and flatness of cookware bottom are specified in table (Z)3. The materials of side wall, cookware bottom and lid are different. In version 2018, the side wall of cookware is made of stainless steel AISI type 304, the cookware bottom is made of stainless steel AISI type 430, and and the lid is made of aluminium. In version 2013, the side wall of cookware is made of 1.4301 stainless steel, the cookware bottom is made of stainless steel 1.4016, and the lid is made of aluminium. Items Version 2018 Version 2013 Remark material thickness material thickness Side wall   stainless steel AISI  304 1mm±0.05mm 1.4301 stainless steel 1mm±0.05mm C ylindrical without handles or protrusions. Cookware bottom stainless steel AISI  ...
发表评论
阅读全文

vertical impact hammers

The vertical impact hammer is designed according to IEC60068-2-75 test Ehc, the hammer consists by a striking element which falls freely from rest through a vertical height on to the specimen surface held in a horizontal plane, and the fall of the striking element shall be along a guideway, the guideway shall not rest on the specimen and the striking element shall be free of the guideway on the striking the specimen , the mass of striking element is equal to equivalent mass . 2J striking element equip with Φ 40 mm*4 71 mm guideway, 5J striking element equip with Φ6 8 mm*3 85 mm guideway, 10J striking element equip with Φ8 9 mm* 337 mm guideway, 20J striking element equip with Φ10 8 mm* 520 mm guideway, 50J striking element equip with  Φ12 9 mm* 650 mm guideway. 
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文