跳至主要内容

Frequently Asked Questions for IPX1 to IPX6 waterproof Testing Equipment

 IPX12 (floor-stand type)

1. How does your equipment achieve the 15-degree tilt required by the IPX2 test?

Pego: The turntable can tilted 15 degrees in 4 positions.

 

2. Does the test needle easy to replace?

Pego: Yes, the nozzle can be changed easily. 100 spare needles and 20 spare brass needle holders will be shipped together with the equipment.

 

3. Can the height of the turntable be adjusted?

Pego: No, the height of turntable is fixed. But the drip board can be lifted up and down. It will automatically stop at a distance of 20mm from the sample.

 

4. How to clean up the accumulated water in the drip board?

Pego: It has the function of air-drying by connecting with air compressor. After the test is completed, the excess water in the drip board can be drained out to avoid long-term accumulation of water and scale and block the pinhole.

 

5. Does the equipment includes water filter?

Pego: Yes, the water filter is included to filter the impurity in the water, and it is easy to replace. In additional, a spare water filter will be shipped together with the equipment.

 

6. Does the device support live testing? Is there a winding problem?

Pego: Yes, the equipment can support live testing, there is waterproof socket-outlet (220V/10A) built-in the turntable, and the power on and power off time can be set on the touch screen. In order to prevent winding, the turntable can be rotated forward or reversed.

 

7. Does the equipment come with a water tank?

Pego: No, the equipment has no water tank. The equipment can connect with tap water directly, normally, the flow rate of tap water can reach the standard requirement.

 

8, Is there any requirements for installtion site?

Pego: Yes. 1). the ground is level, the drainage is unobstructed, the ground and walls are waterproofed, and the floor drain or drainage ditch is set. 2). The user is required to configure a water source for the equipment at the installation site, with a water pressure not less than 0.2Mpa, and install a 4/8 inch faucet.

 

IPX34(floor-stand type)

1. Does the oscillating tubes can be changable?

Pego: Yes.

 

2. Can the height of the turntable be adjusted?

Pego: Yes, the height of turntable can be adjusted.

 

3. Does the test needle easy to replace? Any special tool should be used?

Pego: Yes, the nozzle can be changed easily. 100 spare needles and 20 spare brass needle holders will be shipped together with the equipment. No need tool.

 

4. Does the device support live testing? Is there a winding problem?

Pego: Yes, the equipment can support live testing, there is waterproof socket-outlet (220V/10A) built-in the control pillar, and the power on and power off time can be set on the touch screen. In order to prevent winding, the turntable can be rotated forward or reversed.

 

5. Does the equipment come with a water tank?

Pego: Yes, the equipment has a 30L water tank.

 

6. Does the equipment includes water filter?

Pego: Yes, the water filter is included to filter the impurity in the water, and it is easy to replace. In additional, a spare water filter will be shipped together with the equipment.

 

7. Is there any requirements for installtion site?

Pego: Yes. 1). the ground is level, the drainage is unobstructed, the ground and walls are waterproofed, and the floor drain or drainage ditch is set. 2). The user is required to configure a water source for the equipment at the installation site, with a water pressure not less than 0.2Mpa, and install a 4/8 inch faucet.


IPX56 (floor-stand type)

1. Does the equipment come with a water tank?

Pego: Yes, the equipment has a 550L water tank.

 

2. How to control the test distance?

Pego: Manual control the test distance 2.5m to 3m.

 

3. What is the largest sample that can be tested by the equipment?

Pego: There is no limitation on sample size.

 

4. Does the equipment includes water filter?

Pego: Yes, the water filter is included to filter the impurity in the water, and it is easy to replace. In additional, a spare water filter will be shipped together with the equipment.

 

5. Is there any requirements for installtion site?

Pego: Yes. 1). the ground is level, the drainage is unobstructed, the ground and walls are waterproofed, and the floor drain or drainage ditch is set. 2). The user is required to configure a water source for the equipment at the installation site, with a water pressure not less than 0.2Mpa, and install a 4/8 inch faucet.

 

 

评论

发表评论

此博客中的热门博文

JIS D0203 rain nozzle and spray nozzle test chamber

https://www.pegotester.com/JISD0203_rain_and_spray_test_chamber.html The spray nozzle and rain nozzle test chamber is designed to meet the test requirements of JISD0203 R1/R2 rain test and S1/S2 spray test. The rain nozzle has 2 holes and spray nozzle has 40 holes. Type Symbol Test Purpose Test Method Rain Test R1 Auto parts against water direct contact water pressure: 0.01Mpa, water flow: 1.9L/min, water temperature: ordinary temperature, test time: 10min R2 Auto parts against rain or spray water   indirect contact water pressure: 0.03Mpa, water flow: 3.2L/min, water temperature: ordinary temperature, test time: 10min Spray Test S1 Auto parts against rain or jet water direct contact water pressure: 0.10Mpa, water flow: 24.5L/min, water temperature: ordinary temperature, test time: 30min S2 Auto parts against riptide water pressure: 0.30Mpa, water flow: 39.2L/min, water temperature: ordinary temperature, test time: 1h  
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文

what equipment can be used for IPX3 and IPX4 water ingress protection test?

1. Spray nozzle 1.  Introduction The spray nozzle hand-held device is designed according to IEC60529 figure 5, it is it is apply to verify the protection against spraying water (IPX3) and splashing water (IPX4) for large size sample. The hand-held device is consisted by spray nozzle, moving shield, counterweight, hose and pressure gauge. The spray nozzle is made of brass and has 121 holes with diameter 0.5mm (1 hole at center, 1 inner circles of 12 holes at 30 0  pitch, 4 outer circles of 24 holes at 15 0 pitch). The moving shield is made of aluminum, the counterbalanced shield is in place for IPX3 test, the water pressure is adjusted to give the specified delivery rate, the pressure to achieve this delivery rate will be in the range of 50kPa to 150kPa, and it should be kept constant during the test, the test duration is 1min/m 2  of the calculated surface of the enclosure and with a minimum duration of 5 min. For IPX4 test, the counterbalanced shield is removed fro...
发表评论
阅读全文