跳至主要内容

IPX8 High Pressure Transparent Water Tank

1. Introduction

IPX8 High Pressure Transparent Water Tank can meet the requirement of IEC60529 for IPX8 testing and IEC60598. The pressure in the jar can be precisely automatically controlled in purpose of checking the tightness and the leak points (by observe the bubbling during the test).The equipment is mainly consisted by transparent Sealed jar and control unit.

 


2.  Features

● For IPX8 test.

● Working principle: The sample is placed into the water, close the lid and setup the test pressure and pressure holding time, then start the equipment. When the sample is in water, increase the air pressure on the water surface to the set value and then maintain the pressure. If there is a leak in the sample, the water will be pressed into the sample, and the air in the sample will be discharged, and the leakage point of the sample can be observed through bubbles. After the test is completed, the pressure can be automatically stopped, and the air inside the jar can be automatically drained. The operator can open the lid and take out the test sample.

● The jar is made of acrylic, it is full transparent for observe purpose.

● Adopts special silicone sealing ring which has good elasticity and not easy to damage.

● The jar has passed the pressure test by applying 2 times the working pressure, and equip with branded safety valve to protection the user.

● Control unit: controlled by digital pressure gauge and time relay, the pressure in the jar and pressure holding time can be setup. One-key start to complete the test automatically.

● Pressure control: pressure sensor made by Panasonic, can auto control the test pressure. Control accuracy: ±0002Mpa, display accuracy: 0.001Mpa.

 

3. Parameter

Outer size

500mm*550mm*600mm (L*W*H)

Inner size

Φ270mm*300mm

Wall thickness

15mm

Jar Material

acrylic

Flange thickness

20mm

Flange material

Stainless steel

Weight

40KG

Pressure control mode

auto

Pressure error

±0.002 Mpa

Sensor display accuracy

0.001Mpa

Test water depth

0-30m

Pressure adjustment range

0.01MPa-0.3MPa

Safety valve exhaust pressure

0.35MPa

Pressure hold time

0-999min

Protection device

Leakage switch protection, mechanical safety valve protection

Working Power

AC220V/50Hz (single phase), 100W

Working condition

Temperature: 5℃~35℃

Relative humidity: ≤85%

Pressure: 86kPa~106kPa

Test water

Tap water or pure water

Air source

The air compressor is provided by the user, and the recommended output air pressure: 0.6Mpa—0.8Mpa. Install the female quick connector

标签：

评论

发表评论

此博客中的热门博文

JIS D0203 rain nozzle and spray nozzle test chamber

https://www.pegotester.com/JISD0203_rain_and_spray_test_chamber.html The spray nozzle and rain nozzle test chamber is designed to meet the test requirements of JISD0203 R1/R2 rain test and S1/S2 spray test. The rain nozzle has 2 holes and spray nozzle has 40 holes. Type Symbol Test Purpose Test Method Rain Test R1 Auto parts against water direct contact water pressure: 0.01Mpa, water flow: 1.9L/min, water temperature: ordinary temperature, test time: 10min R2 Auto parts against rain or spray water   indirect contact water pressure: 0.03Mpa, water flow: 3.2L/min, water temperature: ordinary temperature, test time: 10min Spray Test S1 Auto parts against rain or jet water direct contact water pressure: 0.10Mpa, water flow: 24.5L/min, water temperature: ordinary temperature, test time: 30min S2 Auto parts against riptide water pressure: 0.30Mpa, water flow: 39.2L/min, water temperature: ordinary temperature, test time: 1h  
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文

what equipment can be used for IPX3 and IPX4 water ingress protection test?

1. Spray nozzle 1.  Introduction The spray nozzle hand-held device is designed according to IEC60529 figure 5, it is it is apply to verify the protection against spraying water (IPX3) and splashing water (IPX4) for large size sample. The hand-held device is consisted by spray nozzle, moving shield, counterweight, hose and pressure gauge. The spray nozzle is made of brass and has 121 holes with diameter 0.5mm (1 hole at center, 1 inner circles of 12 holes at 30 0  pitch, 4 outer circles of 24 holes at 15 0 pitch). The moving shield is made of aluminum, the counterbalanced shield is in place for IPX3 test, the water pressure is adjusted to give the specified delivery rate, the pressure to achieve this delivery rate will be in the range of 50kPa to 150kPa, and it should be kept constant during the test, the test duration is 1min/m 2  of the calculated surface of the enclosure and with a minimum duration of 5 min. For IPX4 test, the counterbalanced shield is removed fro...
发表评论
阅读全文