跳至主要内容

The figure numbers of the gauges in different version of UL498

 The gauges mentioned in UL498 has a bit difference on the figure numbers in different version, below is a comparison table for reference.

Name

UL498-2001

UL498-2012

UL498-2019

Articulate probe with web stop

Figure 9.1

Figure 9.1

Figure 9.1

Probe

Figure 10.1

Figure 10.1

Figure 10.1

Flat probe

Figure 31.1

Figure 31.1

Figure 31.1

Reference plug

Figure 69.1

Figure 73.1

Figure 74.1

Improper insertion test bland

Figure 94.1

Figure 98.1

Figure 100.1

Test gauge

Figure 105.1

Figure 109.1

Figure 111.1

Test blade

Figure 105.2

Figure 109.2

Figure 111.2

Receptacle test fixture

Figure 118.1

Figure 122.1

Figure 124.1

Pushout tool

Figure 118.3

Figure 122.3

Figure 124.3

Bridge

Figure 118.5

Figure 122.5

Figure 124.5

Test pin A

Figure 119.1

Figure 123.1

Figure 125.1

Test Pin B

Figure 119.2

Figure 123.2

Figure 125.2

57g ground pin

Figure 119.3

Figure 123.3

Figure 125.3

113g ground pin

Figure 119.4

Figure 123.4

Figure 125.4

NO.14 AWG test pin

Figure 129.2

Figure 133.2

Figure 136.2

Small Test probe

Figure132.1

Figure 136.1

Figure 139.1

Large test probe

 

Figure 136.2

Figure 139.2

Fixture for assembly securty test

Figure 144.2

Figure 165.2

Figure 174.2


https://www.pegotester.com/UL498_plug_test_gauges.html#_pp=0_393_21


标签：

评论

发表评论

此博客中的热门博文

The material of standardized cookware in EN60350-2 version 2018 and version 2013

The standardized cookwares referred in this article are designed according to EN(IEC)60350-2 table (Z)3. The diameter of the cookware bottom (outside), diameter of the lid, lid hole circle diameter, number of holes on the circle, total cookware height (outside) and flatness of cookware bottom are specified in table (Z)3. The materials of side wall, cookware bottom and lid are different. In version 2018, the side wall of cookware is made of stainless steel AISI type 304, the cookware bottom is made of stainless steel AISI type 430, and and the lid is made of aluminium. In version 2013, the side wall of cookware is made of 1.4301 stainless steel, the cookware bottom is made of stainless steel 1.4016, and the lid is made of aluminium. Items Version 2018 Version 2013 Remark material thickness material thickness Side wall   stainless steel AISI  304 1mm±0.05mm 1.4301 stainless steel 1mm±0.05mm C ylindrical without handles or protrusions. Cookware bottom stainless steel AISI  ...
发表评论
阅读全文

vertical impact hammers

The vertical impact hammer is designed according to IEC60068-2-75 test Ehc, the hammer consists by a striking element which falls freely from rest through a vertical height on to the specimen surface held in a horizontal plane, and the fall of the striking element shall be along a guideway, the guideway shall not rest on the specimen and the striking element shall be free of the guideway on the striking the specimen , the mass of striking element is equal to equivalent mass . 2J striking element equip with Φ 40 mm*4 71 mm guideway, 5J striking element equip with Φ6 8 mm*3 85 mm guideway, 10J striking element equip with Φ8 9 mm* 337 mm guideway, 20J striking element equip with Φ10 8 mm* 520 mm guideway, 50J striking element equip with  Φ12 9 mm* 650 mm guideway. 
发表评论
阅读全文

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5

UL746A High Current ARC Ignition Test Apparatus 32.5A/COSφ0.5   1.  Introduction: The high current arc ignition tes t apparatus is designed according to  IEC60950-1:2001  clause 4.7.3.6 , BS/EN60950-1:2001, BS7002:2001, GB4943-2001 and UL746A, IEC60947.1:1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-1998 and etc..  It ’ s used to measure and assess  solid insulating material against to resistance to ignition from arcing electrical sources. A power 240V(AC)/60Hz is to be supplied to the test electrodes  (fixed electrode and movable electrode) , a series (inductive-resistive) air core impedance is to be provided to yield a short circuit current of 32.5A and a power factor of 0. 5. The sample is be to positioned with the electrodes making initial contact on the surface of the sample, the circuit is to be energized and the cyclic arcing started. The timing of arcs is to be adjusted to a rate of 40 arcs/min, the rate of electrode separation is to be 254±...
发表评论
阅读全文